Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19

Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19

Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19

Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19

Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19

Warning: Function ereg() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 4

Warning: Function split() is deprecated in ..../includes/class_postbit.php(345) : eval()'d code on line 19
problems with reprogramming remote
Results 1 to 6 of 6

Thread: problems with reprogramming remote

  1. #1
    Noobinator
    Join Date
    Oct 2011
    Posts
    3
    Rep Power
    0

    Post problems with reprogramming remote

    Hi - new here. Just bought a 2001 Outback which I absolutely love! Has 172k on it and runs great. Trying to program a new remote but can't get the security system to shut off/stop blinking on the instrument cluster, so I can't get the reprogramming done.

    I'm following the instructions in the manual but the little light never stops blinking. Any suggestions?

    Thanks for the help!

    Mike Doolin

  2. #2
    TSF Top Poster
    Join Date
    Oct 2011
    Location
    San Francisco Area
    Posts
    105
    Rep Power
    0

    Default keyless transmitter registration

    If you are not using the SM3 computer, there are 12 steps to programming a remote.

    1.make sure you have the remote ID code[8 digits]
    2.close all doors
    3.get in the drivers seat, and close the door
    4.perform the following steps within 45 seconds:
    a.open and close the drivers door once
    b.turn the ignition to "on" 10 times within 15 seconds[a buzzer will sound]
    5.open and close the driver door once within 15 seconds of the end of buzzer opperation[electronic tone will sound for 30 seconds]
    6.before the tone stops sounding,press the door "lock" button the same numer of times as the left most digit of the remote ID code
    7.press the door "unlock" button within 5 seconds of finnishing the lock sequence
    8.perform parts 6 and 7 for every remaining digit of the remote ID code[left to right,when finnished with the 8th digit a electronic tone will sound for 30 seconds]
    9.befor the tone stops sounding, start entering the entire code again the same way
    10.after you have entered the code the second time,an electronic code will sound for 1 second indicating completion
    11.for additional remotes, start now at step 3
    12.turn off ignition and remove the key. close the door and test the remote.
    9.

  3. #3
    Noobinator
    Join Date
    Oct 2011
    Posts
    3
    Rep Power
    0

    Default thanks - I'll try this!

    Quote Originally Posted by 2007fuji View Post
    If you are not using the SM3 computer, there are 12 steps to programming a remote.

    1.make sure you have the remote ID code[8 digits]
    2.close all doors
    3.get in the drivers seat, and close the door
    4.perform the following steps within 45 seconds:
    a.open and close the drivers door once
    b.turn the ignition to "on" 10 times within 15 seconds[a buzzer will sound]
    5.open and close the driver door once within 15 seconds of the end of buzzer opperation[electronic tone will sound for 30 seconds]
    6.before the tone stops sounding,press the door "lock" button the same numer of times as the left most digit of the remote ID code
    7.press the door "unlock" button within 5 seconds of finnishing the lock sequence
    8.perform parts 6 and 7 for every remaining digit of the remote ID code[left to right,when finnished with the 8th digit a electronic tone will sound for 30 seconds]
    9.befor the tone stops sounding, start entering the entire code again the same way
    10.after you have entered the code the second time,an electronic code will sound for 1 second indicating completion
    11.for additional remotes, start now at step 3
    12.turn off ignition and remove the key. close the door and test the remote.
    9.
    This looks promising. I'll try it. Thanks for the help.

  4. #4
    TSF Top Poster
    Join Date
    Oct 2011
    Location
    San Francisco Area
    Posts
    105
    Rep Power
    0

    Default

    If you cant get it to work, contact the dealer...lol

  5. #5
    Noobinator
    Join Date
    Oct 2011
    Posts
    3
    Rep Power
    0

    Default

    Thanks to all. I finally figured it out. The manual neglects to tell you that you need to have the horn/lights signaling turned on and you can't be in valet mode. Both of these conditions must be set before the reprogramming sequence will work.

    I love this car! Can't imagine now why I never looked at Subarus - been buying cars for 50 years and this is the first Subaru. Won't be the last.

  6. #6
    TSF Top Poster
    Join Date
    Oct 2011
    Location
    San Francisco Area
    Posts
    105
    Rep Power
    0

    Default

    Congrats! good job!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •